Machineryline » Catalogue » Atlas Copco

Atlas Copco

4.1

7 reviews

Average rating of Atlas Copco based on key metrics:

3.6

3.6 Price

4.6

4.6 Reliability

4.4

4.4 Maintenance

3.9

3.9 Operation

3.9

3.9 Convenience

Atlas Copco reviews

Read all reviews

Average score of Atlas Copco

4.1

(!) Important: the rating has been formed based on users' ratings and reviews and may reflect subjective experience of usage

3.6

Price

4.6

Reliability

4.4

Maintenance

3.9

Operation

3.9

Convenience

Add a review

4.0

Compressor Atlas Copco GA

2008 Year

3.0 Price

5.0 Reliability

4.0 Maintenance

4.0 Operation

4.0 Convenience

If you’re running multiple compressors, Optimiser 4.0 is the part I’d talk about first. It’s not just a single machine thing, it actually helps pick the efficient combo across compressors/dryers/filters etc. We tied it into LAN and it made it easier to see what’s wasting power without walking the whole room.

On the GA 160 VSD+ itself, it’s aimed at harsh environments and it kinda shows. The dust/moisture protection is legit, and the five-year warranty takes some stress off when it’s running long hours.

Service access is better than some brands, but you still need space around it for that full portal access to be useful. If it’s jammed in a corner, you won’t love it. Overall it’s reliable, just don’t expect bargain pricing.

4.2

Compressor Atlas Copco XAS

2014 Year

4.0 Price

5.0 Reliability

5.0 Maintenance

4.0 Operation

3.0 Convenience

I've rented out the XAS on bigger projects and it's done its job. Solid output and seems built pretty tough. Couple times the weather got bad and it kept running like nothing happened. Accessibility for basic maintenance is good, don't need special tools or anything. Not super cheap but not insane expensive either, seen worse. Not the lightest unit though, so moving it is annoying if you do it solo.

4.0

Compressor Atlas Copco GA

2007 Year

3.0 Price

4.0 Reliability

4.0 Maintenance

4.0 Operation

5.0 Convenience

Installed one of these Atlas GA units a couple months back at our workshop. The space was really open, so fitting it in wasn't a hassle. I like that you don't need a fancy foundation or extra nonsense. Just put it down and connect up the venting. Chucked the warm air outside. Not much you need to mess with day-to-day, mostly runs alone. Found the control panel easy to get the hang of after a couple tries. Service intervals seem reasonable so far, but time will tell if it stays that way. Not super cheap, but for what you get, it's alright-ish. Only thing is, would've liked some better labeling on the panels.

4.2

Compressor Atlas Copco GA

2007 Year

3.0 Price

5.0 Reliability

5.0 Maintenance

4.0 Operation

4.0 Convenience

I'm using the Atlas Copco GA range in an industrial setup, mostly for some heavy-duty mining applications. The IP66 thing is solid - these units deal with dust and grime like it's nothing, which is key out here. I do like not having to crack the whole thing open for regular maintenance; everything's jammed in one spot and the portal design saves you time. The remote monitoring is there if you wanna use it, but feels a bit much for me. Motors haven’t failed on me yet, which is rare. Price is a bit high, I guess, but at least stuff lasts.

4.4

Compressor Atlas Copco GA

2011 Year

4.0 Price

5.0 Reliability

5.0 Maintenance

4.0 Operation

4.0 Convenience

Been around a few Atlas Copco setups and the GA 15-26 is the kind of unit you put in and then mostly forget about, in a good way. The direct drive through a gearbox feels solid and you don’t get the usual belt drama or stretching checks all the time. Air quality is clean if you run the integrated dryer with the auto condensate drain, and the water separator being standard helps too. Service-wise it’s not a pain - oil separator and the usual bits are easy to get to, so you’re not wasting half a day just to reach stuff.

Read all reviews (7)